Doctor Who Cuttings Archive

R/C Dalek

From The Doctor Who Cuttings Archive
Revision as of 22:26, 20 July 2022 by John Lavalie (talk | contribs) (Created page with "{{article | publication = Radio Control Models and Electronics | file = | px = | heig...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigationJump to search



YOU are still in time for Christmas if you start building a Dalek now ... This model is easily constructed from card and balsa plus a few junkbox oddments. Two Mabuchi 55 motors provide the power and drive a pair of main wheels by friction. The wheels on the original model are Keil Kraft spong rubber streamline types 2 in. diameter and the motors are fixed so that their armature shafts exert light pressure on the tyres. A castoring tail wheel I in. diameter is mounted on a piano wire leg pivoted in a block of wood. 1/16 in. plywood is used to reinforce the balsa "floor" and the whole superstructure lifts off for access.

Power for the drive motors is supplied by two separate 4.5 v. flat batteries with negatives common to the motors via an on/off switch.

The radio link may be chosen to suit existing outfits, the only requirement being that the receiver has a single pole changeover relay or is capable of operating a low resistance relay (50 to 100 ohms) if the particular receiver used is a relayless type ... A simple pulser keys the transmitter ... The pulser may be mechanical or transistorised, the only requirement being that fairly low rate of mark/space be used. The original system employs a MacGregor carrier transmitter keyed via a 2,000 ohm Siemens relay in a two transistor multivibrator circuit.

The receiver is an old Aeromodeller Transistor Rx operating another 2,000 ohm Siemens relay. More recent circuits could easily be employed, but that which the author used was available for this "fun" model at the time.


The relay in the receiver feeds negative bias alternately to a transistorised switcher. The switcher is in two parts each half feeding one of the drive motors. Capacitors Cl and C2 remain charged when pulsing at 50/50 mark/space so that both halves of the switcher pass current to their appropriate motors continuously. RI and R2 values are adjusted so that when the mark/space signal is varied such that the relay contacts dwell longer on one side than the other, the capacitor on the contact which has the shortest dwell discharges completely, cutting off the appropriate transistor and hence the supply to that drive motor.

Thus, both drive motors run at full speed for straight running, a turn is accomplished by blipping one or other of the motors off due to unbalance of the mark/space signal. The switcher also protects the relay contacts, as there is only a small bias current passing through them.

Control is thus fully proportional and slight discrepancies in speed of the two drive motors, either due to varying efficiency, or varying battery voltages, can be compensated for by varying the mark/space signal so that it is not exactly 50/50. For best results: either the pulse rate, or the resistors RI and R2 should be adjusted so that the capacitors Cl and C2 only just hold their charge long enough to keep the motors running continuously. If the charge is held for too long, the neutral will be too wide, but control can be effected by giving solid signal or no signal as required. Such a method of control is less flexible however, so little time spent in adjusting the system for proportional response is well worth while.

This control system might work in a model delta using flyball actuators, one for each elevon. It would certainly be suitable for track vehicles, paddle boats or indeed any other device which is controlled by varying the speed of two drive motors. One could even build a wide beam boat with twin screws, each mounted well forward and as near the sides as possible.

Disclaimer: These citations are created on-the-fly using primitive parsing techniques. You should double-check all citations. Send feedback to

  • APA 6th ed.: (Jan. 1966). R/C Dalek. Radio Control Models and Electronics p. 19.
  • MLA 7th ed.: "R/C Dalek." Radio Control Models and Electronics [add city] Jan. 1966, 19. Print.
  • Chicago 15th ed.: "R/C Dalek." Radio Control Models and Electronics, edition, sec., Jan. 1966
  • Turabian: "R/C Dalek." Radio Control Models and Electronics, Jan. 1966, section, 19 edition.
  • Wikipedia (this article): <ref>{{cite news| title=R/C Dalek | url= | work=Radio Control Models and Electronics | pages=19 | date=Jan. 1966 | via=Doctor Who Cuttings Archive | accessdate=25 June 2024 }}</ref>
  • Wikipedia (this page): <ref>{{cite web | title=R/C Dalek | url= | work=Doctor Who Cuttings Archive | accessdate=25 June 2024}}</ref>